TURING FIREWIRE 800 TO USB PORT FOR MAC
TURING FIREWIRE 800 TO USB PORT PRO
TURING FIREWIRE 800 TO USB PORT PC
TURING FIREWIRE 800 TO USB PORT BLUETOOTH
TURING FIREWIRE 800 TO USB PORT MAC

TURING FIREWIRE 800 TO USB PORT BLUETOOTH

They go on to list the keyboard/trackpad, memory card reader and Bluetooth all connected to the front port, while the rear has the iSight and IR receiver, indicating a possible overload on the front port.Ī quick Google search found a user on MacRumors forum with very similar results. The first port is almost twice slower than the second one, limited to 15 MB/s in writing and 22 MB/s in reading, while the other port reaches the maximal performance level offered by the USB 2.0 enclosure. On the most distant USB port from the user: On the USB port located close to the user sitting in front of his MBP, the following results are obtained: To illustrate the difference, hereafter are captures of a test performed with a SSD drive installed in an external enclosure USB 2.0: The article from Hardmac has graphical representation that the rear port has a much higher read/write performance than the front. Core i5 and i7 MacBook ProsĭJRiO sent us an article on the new Core iX family of MacBook Pros that indicates the newer models are subject to one “good” port and one “bad” port too, but that the good and bad are reversed from the old norm. The relatively small difference indicates that either port could successfully be used for a sound card and that Apple seem to have distributed the USB peripherals evenly on the latest builds.

The results were very similar (74 samples or 3.30 ms latency for the front and 88 samples or 3.38 ms latency for the rear), but the front port repeatably required a few less samples before the drop outs stopped. After setting the sample rate to 192 kbps and the CPU load to 80%, I reduced the samples to minimum (lowest latency) and started increasing until there were no more drop-outs. For those unfamiliar, Live provides a test tone with a simulated CPU load for testing audio latency. To quantify the difference between the ports on my Dec 2009 MBP 13”, I used Ableton Live’s audio test tone with a NI Audio Kontrol 1 on both ports. These recommendations have stood since the early days of the MBP, with the trackpad and iSight specifically pointed out as devices causing poor port performance. For MB and MBP models with the both ports on the left (as in the above photo), only the port furthest from the screen is recommended (often referred to as the front port).

TURING FIREWIRE 800 TO USB PORT MAC

Then, after disabling USB energy saver mode, they can shout back “Get a PC” at the Mac users! Core/Core Duo MacBooksįor MBP models with ports on the left and right, only those on the left are recommended.

TURING FIREWIRE 800 TO USB PORT PC

PC users may rejoice at this one, but should first check their internal USB hub is functioning optimally. Serato do not go into specifics as to which port to use, but acknowledge that one port is “good” and the other “bad”.

TURING FIREWIRE 800 TO USB PORT FOR MAC

Native Instruments thinks that the issue is serious enough to include recommended USB ports for Mac users in all it’s soundcard manuals in the Troubleshooting section.

And depending on the configuration of the laptop, the devices are piggybacked differently onto your 2 USB ports. Hardware like the keyboard/trackpad, iSight, memory card reader, Bluetooth and the IR receiver are all USB devices attached to the internal hub.

With only 2 USB ports on the 13″ and 15″ MB and MBP, Apple have shuffled around USB users on its internal USB hub scheme over the years. And we know that when the latency is too high, our actions become noticeably out of sync with the audio. When audio drop outs occur, often our only remedy is to increase latency. If we want to have a high sample rate working at a low latency, the port needs be reading and writing quickly. How does this affect you? The ability for a port to receive and transmit at specified rates affects our audio settings. For example, the Numark Omni will only provide 4 channel output if it detects a USB 2.0 connection, defaulting to 2 channels if it detects anything lower. Most high end sound cards require USB 2.0 to even operate, with some cards even have multiple configurations. New evidence is showing, that especially with the new i5 and i7 models, you might be missing out on performance by choosing the wrong port.Īs digital audio performance increases, with higher sampling rates and greater bit depth, the speed of our USB port becomes more significant.

TURING FIREWIRE 800 TO USB PORT PRO

For MacBook and MacBook Pro users, the choice of which of the two available USB ports to use for your sound card hook-up may have never occurred to you. An audio issue is every DJ’s worst nightmare, after all audio is our art! For digital DJs, there are two sets of audio to worry about: analogue and digital, with USB being the most popular means for our digital hook-up.

Turing firewire 800 to usb port